+7(4722)42-11-79
Order a consultation
RU EN

KAEL-3 MOBILE CABLE ELECTRIC LABORATORY

Delivery time 45 days
Order consultation
appointment
Specifications
Equipment

GENERAL TECHNICAL DATA   KAEL-3

Power supply - single-phase AC network with a frequency of 50 ± 2 Hz, voltage ............. 220 ± 20V

Consumption current, no more, A, .......................................... .................................................. ........... 60

The maximum value of the measured error of the output

voltage and current,%, not more .......................................... .................................................. ............. 3

The length of the mains connecting cable on the drum is 30 m, the cross-section is 7.5 mm 2 , 

cable type - PRRP  

Length of protective grounding wire on the drum - 30 m, cross-section -10 mm 2 , type -PV-4

Length of high-voltage coaxial cable PVVEV on 3 drums - 30 m each, cross-section - 3.5 mm 2

Length of high-voltage wire PVV-1 for testing with alternating voltage ........... 30 m

The occupied area in the plan, m ............................................ .................................................. 1.8x3.0

Equipment weight, kg, no more ........................................... .................................................. ... 500

Service staff................................................ ........................... 2 operators (at least)

Laboratory service life, years ………………………………………………………………… ..10

No.

                     Name

Qty.

    Note

1

Control stand included:

  • high-voltage switch for selecting modes - 3;
  • high-voltage switch "BURN-CHARGE GAUV" - 1; 
  • regulating autotransformer TDGC2-5 (RNO) - 1;
  • three-phase short-circuit breaker with electric drive - 1

1

 

2

Electrical laboratory control unit 

1

 

3

  OTDR high-voltage oscillographic
  "Iskra-3M" complete with sensors

1

 

4

Sound frequency generator GZCH-2500

1

 

5

Receiver "P-806" complete with sensors

1

 

6

High-voltage test unit BVI-60/50-M5

1

 

7

Burning unit BPR-25/8

1

 

8

Acoustics generator GAUV - 20-16

1

 

8

Drum unit with protective earth wire and mains cable

1

Length - 30 m each

10

Block of three drums with cables for testing and insulation burning

1

Length - 30 m each

11

High-voltage wire for testing with alternating high voltage

1

 Length-30 m

(in the bay)

12

Siren SS-1

1

 

13

Signal lamp red

1

 

14

Fencing kit:

  • insulating pin - 4 pcs .;
  • insulating cord - 20 m

1

 

15

Insulation stand complete with base

4

 

16

Electric laboratory cable mobile KAEL-3 (ETL-10). 

The passport. KAEL-3 (ETL-10) /186.00.00.00PS

1

 

17

Electric laboratory cable mobile KAEL-3 (ETL-10).
 Manual. KAEL-3 (ETL-10) /186.00.00.00RE

1

 

18

  OTDR high-voltage oscillographic
  "Iskra-3M" Operation manual.

1

 

19

Sound frequency generator GZCH-2500.
Manual.

1

 

20

Receiver "P-806". Manual.

1

 

The mobile cable electric laboratory KAEL-3 (hereinafter - "KAEL-3") is installed in the van of a car and is intended for:

  • testing of cable insulation (including with XLPE insulation) and other devices and devices with direct and alternating (50 Hz) high voltage
  • burning of defective cable insulation with its subsequent afterburning;
  • determination of the route of cable lines;
  • topographic determination of places of damage to cable lines by induction and acoustic methods;
  • determination of the distance to the place of damage of cables with a voltage of 0.4-10 kV by a pulsed non-burn method at high and low voltage

Terms of Use:  

  • ambient temperature range, о С ………………………… ... from minus 20 to +40;
  • relative air humidity at a temperature of 25  о С ……………………………. up to 80%;
  • atmospheric pressure, mm. rt. Art ……………………………………………………… .650 - 800

The place of operation must be free of vapors of corrosive liquids (acids and alkalis).

Operation of KAEL-3 in explosive environments is prohibited !

KAEL-3 is powered from an industrial single-phase network 220V, 50 Hz. It is allowed to be powered from an autonomous power supply generator with a capacity of at least 2.2 kVA or from a ~ 220V network with an isolated neutral. 

To fully realize the capabilities of KAEL-3, the generator power must be at least 25 kVA.